 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| XE1401 4/99 Multi-National 14,400 BPS Embeddable Modem Description Xecom's XE1401 is a complete 14,400 bps modem in a single component. It is available for use in many countries throughout the world. Xecom offers versions for North America and Japan, Germany, France, Italy, and the United Kingdom. The XE1401 is a complete modem including the DAA. XE1401 users do not need to add RAM, ROM, Crystals, transformers, or switches to complete the modem design. The user only needs to provide the TTL level, serial interface and the telephone jack. The XE1401 is a full-featured modem. Besides the 14,400 bps data transfer, the XE1401 supports data compression, error correction and fax transfer. The XE1401 also inlcudes NVRAM for permanent storage of the modem configuration. The XE1401 is pin compatible with Xecom's XE2401L and XE3301 modems. This family of modems permits a simple upgrade path from 2400 bps to 33,600 bps. Features * Models for North America, Japan, and Europe Country Canada Japan France Germany Italy UK USA1 Model XE1401 XE1401 XE1401F XE1401G XE1401I XE1401B XE1401 * Small Size: 2.75 inches by 1.38" by 0.42" * UL1459 Recognized * Modem Protocols: V.32bis (14,400 bps), V.32, V.22bis, V.22, V.21, Bell 212A and 103 * Fax Protocols: V.17 (14,400 bps), V.29, V.27ter, and V.21 channel 2 * Error Correction; V.42, MNP2-4 and MNP10 * Data Compression; V.42bis and MNP5 provides a maximum effective data rate of 57,600 bps. * Pin compatible with Xecom's XE2401L and XE3301 modems 1 (user transferable FCC Registration) Serial I/O /DTR /RTS /CTS /DSR TXD RXD /DCD Block Diagram ROM Modem Controller NVRAM Analog Front End DAA Tip Ring Auxiliary I/O RESET AR /LCS OH XECOM (1) XE1401 XE1401 Mechanical Specifications Inches Dim Min Max A B C D E F G H J K L M 2.74 1.370 0.400 0.890 1.890 0.125 0.080 0.415 0.090 0.020 0.380 0.090 2.760 1.390 0.420 0.910 1.910 0.200 0.100 0.435 0.110 0.025 0.400 0.110 Metric (MM) Min Max 69.60 34.80 10.16 22.61 48.01 3.18 2.03 10.54 2.29 0.51 9.65 2.29 70.10 35.31 10.67 23.11 48.51 5.08 2.54 11.05 2.79 0.64 10.16 2.79 A C J H B K D G L F E M Pins = 0.025 inch square pin All pins tin-plated XE1401 PIN CONFIGURATION RESET N/C RXD 1 2 3 40 39 38 VCC /DSR /DCD /DTR /LCS /CTS OH TXD /RTS NC /RI TIP RING 9 10 11 12 13 14 15 16 18 20 22 21 AMP GND XECOM (2) XE1401 XE1401 Pin Descriptions PIN NAME 1 RESET DESCRIPTION Hardware reset pin, Input, active High, TTL. A high on Pin 1 initiates a hardware reset. An external reset is not required or recommended. The Reset pulse must be a minimum of 100 milliseconds long. No Internal Connection Received Data, Output, TTL. Serial data output to the host. A logic "High" on RXD represents a "mark" and a logic "Low" represents a "space". Data Terminal Ready, Input, active Low, TTL. The "AT&D" command sets the function of \DTR. The default, AT&D2, requires the host to assert \DTR to permit a modem link. The modem drops the call in progress if \DTR is revoked and will not connect until \DTR is reasserted. Loop Current Sense, active Low Input, TTL. A low on \LCS tells the modem that loop current is flowing through Tip and Ring. This feature is used only in the XE1401B version. Clear to Send, Output, active Low, TTL/CMOS. \CTS is used as a Flow Control output from the modem. The modem revokes \CTS with hardware flow control active to signal the host that the modem's input buffer is full. The modem reasserts \CTS when the buffer can accept more data without a buffer overflow. Off-Hook, Output, active High. OH indicates the modem's hookswitch relay is closed. Hookswitch closure connects the modem to the telephone line. Transmit Data, Input, TTL. Serial data input from the host. A logic "High" represents a "mark" and a Low represents a"space", TTL. Request to Send, input, active LOW, TTL. The XE1401 uses \RTS for hardware flow control. When \RTS is revoked and hardware flow control is enabled, the modem will not place data on RXD. No Internal Connection Ring Indicator, Output, active Low, TTL. When low indicates the modem is receiving a ring signal. Tip connection to the phone line (RJ11 pin3) from the internal DAA. The XE1401 is not sensitive to the battery voltage polarity across Tip and Ring. Ring connection to the phone line (RJ11 pin4) from the internal DAA. Ground (0 volts) Audio Output function is set by L & M commands and the value in register S22. This output can drive a minimum load of 300 ohms. 2 3 N/C RXD 9 \DTR 10 \LCS 11 \CTS 12 OH 13 TXD 14 \RTS 15 16 NC \RI 18 TIP 20 21 22 RING GND AMP XECOM (3) XE1401 XE1401 Pin Descriptions PIN NAME 38 \DCD DESCRIPTION Data Carrier Detect, Output, active Low, TTL/CMOS. AT&C sets the \DCD function. In the default condition, AT&C1, \DCD indicates the presence of a carrier signal on the telephone line. Data Set Ready, Output, active Low, TTL/CMOS. AT&S sets the \DSR function. In the default condition, AT&S0, \DSR is forced true. +5 Volts 39 \DSR 40 Vcc ABSOLUTE MAXIMUM RATINGS* SUPPLY VOLTAGE - Vcc DC INPUT VOLTAGE STORAGE TEMPERATURE RANGE LEAD TEMPERATURE (Soldering, 2 sec per wave) OPERATING TEMPERATURE RANGE *Exceeding these values may result in permanent damage to the device. +6.5 Volts -0.6 Volts to +6.5 Volts -25 C TO +85 C 260 C 0 TO 70 C XE1401 ELECTRICAL SPECIFICATIONS Parameter VCC ICC Ring Voltage Detected Min 4.75 100 38 10 20 15.3 10 10 10 10 -12 Typ Max 5.25 Units Volts mamps RMS RMS RMS Hz mamps mamps mamps mamps dBm dBm KHz Comments 150 170 150 On Line XE1401 XE1401B, XE1401I XE1401G XE1401 XE1401B, XE1401I XE1401G XE1401F Avg over 3 second interval XE1401G Only Ring Frequency Detected Telephone Loop Current 68 100 120 60 45 -10.5 -2.5 16 -9.0 0 Data Transmit level DTMF Transmit Level Billing tone Filter XECOM (4) XE1401 XE1401 Typical Applications/DSR Schematic /DCD 16C450 UART VCC SIN RXD /DSR /DCD XE3301 XE1401 /DTR /CTS SOUT /RTS /RI /DTR /CTS TXD /RTS /RI Tip Ring AMP GND .2 ufd +5 Volts 50K LM386 .05 ufd 250 ufd L2 L1 10 ohms 8 ohm .5 W Speaker C1 4 3 Line J1 C2 Note: RJ11 Pin assignments reflect a 6-pin connector. Tip and Ring are always the center pins of the RJ11 jack. Recommended Parts Reference Designation L1, L2 C1, C2 J1 Description Ferrite Beads Capacitors RJ11 Jack Recommended Part Number TDK CB30-1812 Sprague 30GAT47, 470 pfd, 3000 Volts Stewart SS6446NF XECOM (5) XE1401 XE1401 AT Commands Modes of Operation Command Line - A command line may include multiple comThe XE1401 uses "AT" commands for control and configura- mands. The modem executes the commands in the sequence tion. The XE1401 operates in three modes; Command they appear in the command line. Spaces, inserted to improve Mode, Fax Mode and Data Mode. Extensions to the AT command set support fax operation. Data Mode: The modem enters data mode after it establishes a link and issues a "CONNECT" result code. In Data Mode the modem modulates all signals on Transmit Data, Pin 13, and sends them to the remote modem. The modem demodulates the signal from the remote modem and places it onto Received Data, Pin 3, for the host equipment. When the modem exits data mode, it issues a "NO CARRIER" result code. Command Mode: The XE1401 enters command mode on application of power, reset, loss of the connection, or receipt of the escape sequence. In command mode the modem accepts commands from the host on Transmit Data. Appropriate result codes are returned on Received Data at the same speed and parity as the commands. Fax Mode: The modem enters fax mode on receipt of the AT+FCLASS=1 command. Fax commands and responses are issued at 19,200 bits per second; the character format is 8 bits no parity. The modem accepts Class 1 Fax commands only in fax mode. The A/, ATO, AT&T and escape commands are not valid in fax mode. Commands The modem is configured and controlled with AT comOmitted Parameters - Most commands include a parameter which determines the command function. When the parameter is omitted from the command string, it is assumed to be a 0. Escape Characters - A three character escape sequence, entered while in data mode, will switch the modem into command mode while remaining on line. The escape character, set by Register mands. AT commands follow a strict format. The command S2, is entered 3 times in succession to execute the escape. The line is stored in the command buffer and executed upon re- default escape sequence is "+++." ceipt of a carriage return. Until executed, the command line can be edited with the backspace key. Command Format - Each command, except A/, begins with the AT prefix. The "A" and "T" may be both upper case or Result Codes - The modem issues a result code after each action. Result codes may be provided as full words, numeric codes or may be disabled. Each result code ends with a carriage Re-Execute Last Command - The A/ command causes the modem to re-execute the command line stored in the command buffer. This is the only command which does not require the "AT" prefix. Command Line Editing - A backspace can be used to edit the command any time before it is executed. The backspace character, Control and H simultaneously on some systems, erases the previous character in the command line. Any character except for the "A" and "T" can be erased. Register S5 allows the user to select a character other than a backspace to edit the command line. legibility, do not fill space in the command buffer. A carriage return terminates the command line and causes the commands to be executed. Register S3 allows the user to select a character other than a carriage return to terminate the command line. Command Buffer - The command buffer holds 40 characters, including the AT prefix. If it overflows, the modem issues an "ERROR" result code and commands are not executed. both lower case but cannot be of different cases. The modem return when numeric result codes are chosen. When full word result codes are chosen, a Line Feed and Carriage Return preuses the prefix to identify the host's speed and parity. The modem determines speed by measuring the width of the incoming bits and parity by comparing the parity bits of the "A" and "T." The modem then returns result codes at the host's speed and parity. cede and follow each result code. XECOM (6) XE1401 XE1401 AT Commands (continued) List of Commands An asterisk indicates the default setting of the command for the XE1401. The default setting may be different for the European models. A - Answer Command - ATA forces the modem to immediatly go off-hook and transmit answer tone. Bn - Select Communications Standard - ATBn selects the modulation used for connections below 2400 bits per second n=0 n=1 Selects CCITT standards Selects Bell standards* Mn - Speaker Activity - ATMn determines when the modem's audio output is active. n=0 n=1 n=2 n=3 Speaker off Speaker on until carrier received* Speaker remains on Speaker off during dialing, on until carrier Nn - Data Rate - ATNn selects whether or not the modem will negotiate a lower data link speed. n=0 Handshake only at DTE rate n=1 Negotiate highest common speed* On - On Line - ATOn switches the modem from the command mode to the data mode. n=0 n=1 Return On Line with no retrain* Initiate retrain returning On Line. D - Dial Command - Below are the characters accepted in a dialing command. 0-9, #, * = Dialing Digits L= P= T= W= ^= , ! ; = = = @= Re-dial last number Pulse dial Tone dial Wait for dial tone Toggles state of calling tone Pause for the duration of S8 Wait for silence Switch hook flash Return to the command state Qn - Responses - ATQn determines if the modem will issue responses. n=0 Send responses* n=1 No Responses Sr=n - Set Register Value - ATsr=n sets the value of register Sr to n. Vn - Result Codes - ATVn sets the modem to issue Numeric or Full Word result codes . n=0 n=1 Numeric Result Codes English Word Result Codes* S=n = Dial stored number En - Command Echo - ATEn determines whether commands will be echoed back to the host. n=0 n=1 Do not echo commands Enable command echo* Wn - Connect Message Rate - ATWn determines whether the data rate reported in the Connect response is the host data rate, the link data rate or whether both are provide along with the error control and data compression protocols negotiated. n=0 n=1 n=2 Send "CONNECT" at DTE Rate* Report line speed, DTE speed and Link protocol "CONNECT" Reports Link speed Hn - Switch Hook Control - ATHn opens and closes the modem's hook switch. n=0 Switch hook relay opens n=1 The switch hook relay closes In - Modem Identification - ATIn Identifies the version of the modem. Ln - Speaker Volume - ATLn sets the amplitude of the modem's audio output. n=0 Lowest speaker volume n=1 Low speaker volume* n=2 Moderate speaker volume n=3 High speaker volume Xn - Result Code Set - ATXn selects which set of result codes the modem may send. n=0 Result codes 0 to 4 n=1 Result codes 0 to 5 and 10 n=2 Result codes 0 to 6 and 10 n=3 Result codes 0 to 5, 7 and 10 n=4 Full Result codes* XECOM (7) XE1401 XE1401 AT Commands (continued) Yn - Long Space Disconnect - ATYn sets the modem to disconnect on receipt of 1.6 seconds of continuous space. n=0 Long Space Disconnect Disabled* n=1 Disconnect on long space Zn - Reset - ATZn executes a soft reset to the modem and resets the modem configuration. n=0 Reset to user profile 0* n=1 reset to user profile 1 &Cn - DCD Operation - AT&Cn determines the operation of the DCD output. n=0 DCD is forced active. n=1 DCD indicates a valid carrier* &Dn - DTR - AT&Dn determines how the modem will respond to changes to DTR. n=0 DTR is ignored by the modem. n=1 Enter command mode if DTR revoked. n=2 Disconnect if DTR revoked.* n=3 Soft reset when DTR revoked &Fn - Return to Factory Defaults - AT&Fn returns the modem configuration to one of two factory configurations. n=0 Restore configuration 0* n=1 Restore configuration 1 &Gn - Guard Tone - AT&Gn controls the guard tone produced by the modem n=0 Guard Tone Disabled* n=1 Guard Tone Disabled n=2 1800 Hz Guard Tone &Kn - Flow Control - AT&Kn selects the flow control method used by the modem. n=0 Disabled n=3 RTS/CTS n=4 XON/XOFF n=5 Transparent XON/XOFF n=6 RTS/CTS and XON/XOFF &Pn - Dial Pulse Make/Break Ratio - AT&Pn determines the specific pulse dialing parameters used by the modem. n=0 39/61% @ 10 pps* n=1 33/67% @ 10 pps n=2 39/61% @ 20 pps n=3 33/67% @ 20 pps &Qn - Line Connection - AT&Qn determines if error control or data buffering aare active on the link. n=0 Direct mode (no data buffering)* n=5 Use Error Correction n=6 Normal Mode (Speed buffering) &Sn - DSR Operation - AT&Sn sets the operation of the DSR signal. n=0 DSR always active* n=1 DSR in accordance with V.25. &Tn - Test Modes - AT&T selects modem test modes. n=0 Exit test mode n=1 Local analog loopback n=3 Initiate local digital loopback n=4 Respond to remote loop request* n=5 Deny remote loop request n=6 Initiate a Remote Digital loopback n=7 Remote digital loopback w self-test n=8 Local analog loopback w self-test &Vn - View Configuration Profiles - AT&V permits the user to check on the modems current configuration. n=0 View active profile & user profile 0* n=1 View active profile & user profile 1 &Wn - Store Active Profile - AT&Wn stores the current modem configuration in NVRAM. n=0 Store active profile as profile 0* n=1 Store active profile as profile 1 &Yn - Recall Stored Profile - AT&Yn sets the stored modem configuration to be used after a hard reset. n=0 Recall profile 0 on power-up* n=1 Recall profile 1 on power-up &Zn=x - Store phone number "x" in memory location "n" %En - Line Quality Monitor/Auto Retrain - AT%En determines if the modem monitors line quality during a connection and intiate a retrain if quality drops below acceptable levels. n=0 Disabled n=1 Enabled n=2 Line quality, fallback, fall forward XECOM (8) XE1401 XE1401 AT Commands (continued) %L - Read Received Signal Level - AT%L permits the user Host initiates break with \B command on Reliable link. to read the magnitude of the recevie singal in dBm. %Q - Read Line Signal Quality - AT%Q permits the user to read the EQM value of the recevied signal. \An - MNP Block Size - AT|An sets the block size for MNP data packets. n=0 Maximum 64 characters n=1 Maximum 128 characters n=2 Maximum 192 characters n=3 Maximum 256 characters* \Bn - Transmit Break - AT\Bn selects the duration of the break signal sent. Break = n x 100 msec. \Kn - Break control - AT\Kn determines how the modem will handle a break signal. Break received from host with Reliable link. n=0 Enter on-line command mode; do not transmit break n=1 Purge buffers, immediately transmit break n=2 Same as n=0 n=3 Immediately send break n=4 same as n=0 n=5 Send break in sequence with data* Break received from host with Direct link . n=0 transmit break, then enter on-line command mode n=1 Immediately send break n=2 Enter command mode; do not transmit break signal n=3 same as n=1 n=4 same as n=0 n=5 same as n=1* Break received from modem w Normal link. n=0 Purge buffers, Immediately send break to the host n=1 same as n=0 n=2 Immediately send break to the host n=3 Same as n=2 n=4 Send break in sequence with data. n=5 Same as n=2* \Vn - Single Line Result Codes - AT/Vn determines if the Connect response is issued in a single line format. The single line format is shown. CONNECT XECOM (9) XE1401 XE1401 Result Codes Digits 0 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 22 23 33 35 40 44 45 Verbose OK CONNECT RING NO CARRIER ERROR CONNECT 1200 NO DIAL TONE BUSY NO ANSWER CONNECT 2400 CONNECT 4800 CONNECT 9600 CONNECT 7200 CONNECT 12000 CONNECT 14400 CONNECT 19200 CONNECT 38400 CONNECT 75TX/1200RX CONNECT 1200TX/75RX FAX DATA CARRIER 300 CARRIER 1200/75 CARRIER 75/1200 Description Successfully executed command line 300 bps connection Ring signal detected Carrier not detected/lost Error in command line 1200 bps connection No dial tone detected Busy signal detected 5 second silence not detected 2400 bps Connection 4800 bps Connection 9600 bps Connection 7200 bps Connection 12,000 bps Connection 14,400 bps Connection 19,200 bps Connection 38,400 bps Connection V.23 originate connection V.23 answer connection Fax connection Data connection in Fax mode 300 bps carrier received V.23 reverse channel carrier received V.23 forward channel carrier received Digits 46 47 48 49 50 51 52 66 67 69 70 77 80 81 +F4 Verbose CARRIER 1200 CARRIER 2400 CARRIER 4800 CARRIER 7200 CARRIER 9600 CARRIER 12000 CARRIER 14400 COMPRESSION: CLASS 5 COMPRESSION: V.42bis COMPRESSION: NONE PROTOCOL: NONE PROTOCOL: LAPM PROTOCOL: ALT Description 1200 bps carrier received 2400 bps carrier received 4800 bps carrier received 7200 bps carrier received 9600 bps carrier received 12,000 bps carrier received 14,400 bps carrier received MNP5 data compression V.42bis data compression No data compression No error correction LAPM error correction MNP error correction PROTOCOL: ALT CELLULAR MNP10 error correction +FCERROR Fax carrier error XECOM (10) XE1401 XE1401 Class 1 Fax Commands AT+FCLASS? - Service Class Indication n=0 n=1 Configured as a data modem Configured for Service Class 1. AT+FRM AT+FCLASS=? - Shows Service Class Capability n=0 n=1 Configured as a data modem Configured for Service Class 1. AT+FCLASS=n - Sets Service Class n=0 n=1 Configured as a data modem Configured for Service Class 1. AT+FAE=n - Selects Data/Fax Auto Answer n=0 n=1 Answer as a fax modem only Either a fax or data modem AT+FRS=n - Receive Silence This command causes the modem to issue an OK response after detecting silence for n * 10 milliseconds. AT+FTS=n - Stop Transmission and Wait This command causes the modem to stop transmission for n * 10 milliseconds before issuing the OK response AT+FRH=n - Receive HDLC Data Frames n=3 n=24 n=48 n=72 n=73 n=74 n=96 n=97 n=98 n=121 n=122 n=145 n=146 V.21 Channel 2, 300 bps V.27ter, 2400 bps V.27ter, 4800 bps V.29, 7200 bps V.17, long training, 7200 bps V.17, short training, 7200 bps V.29, 9600 bps V.17, long training, 9600 bps V.17 short training, 9600 bps V.17, long training, 12,000 bps V.17 short training, 12,000 bps V.17, long training, 14,400 bps V.17 short training, 14,400 bps AT+FTH=n- Transmit HDLC Data n=3 n=24 n=48 n=72 n=73 n=74 n=96 n=97 n=98 n=121 n=122 n=145 n=146 V.21 Channel 2, 300 bps V.27ter, 2400 bps V.27ter, 4800 bps V.29, 7200 bps V.17, long training, 7200 bps V.17, short training, 7200 bps V.29, 9600 bps V.17, long training, 9600 bps V.17 short training, 9600 bps V.17, long training, 12,000 bps V.17 short training, 12,000 bps V.17, long training, 14,400 bps V.17 short training, 14,400 bps AT+FTM XECOM (11) XE1401 XE1401 AT Registers S-Registers Following are descriptions of the S-Registers Supported by the XE1401. S0 Answer on nth Ring: S0 sets the modem to automatically answer on the nth ring. Setting S0 to 0 disables automatic answer. Range: Units Default 0 to 255 Rings 0 S6 Dial Tone Wait Time: S6 determines how long the modem waits for dial tone before dialing begins. The Dial Tone Wait Time cannot be set to less than two seconds. Range: Units Default 2 to 255 Seconds 2 S7 Wait for Carrier after Dialing: S7 determines how long the modem waits for a valid carrier signal after dialing is completed. Range: Units Default 1 to 255 Seconds 50 S1 Ring Count: S1 is a read-only register. It shows the number of rings detected. If a ring is not detected within 8 seconds, the counter is reset to zero. Range: Units Default 0 to 255 Rings 0 S8 Comma Pause Time: S8 defines the duration of the pause initiated by a comma in the dialing string. The pause is generally used when waiting for a second dial tone. Range: Units Default 1 to 255 Seconds 50 S2 Escape Character: S2 determines the ASCII character used in the escape sequence. Values of 0-127 select valid ASCII escape characters; values from 128 to 255 disable the escape sequence. Range: Units Default 0 to 255 ASCII Character 43 (+) S9 Carrier Detect Response Time: S9 establishes the length of time the remote modem's carrier must be present to be recognized as valid. Range: Units Default 1 to 255 0.1 Seconds 6 S3 Carriage Return Character: S3 determines the ASCII character to serve as a carriage return to terminate commands and to be inserted in modem responses. Range: Units Default 0 to 127 ASCII Character 13 (Carriage Return) S10 Carrier Off Disconnect Delay: S10 selects how long carrier must be lost before the modem disconnects. Note: If S10 is smaller than the value of S9, the modem will not automatically disconnect on loss of carrier. Range: Units Default 1 to 255 0.1 Seconds 14 S4 Line Feed Character: S4 sets the ASCII character to act as a line feed character in modem responses. Range: Units Default 0 to 127 ASCII Character 10 (Line Feed) S11 Tone Dialing Speed: S10 sets the duration and spacing of the dialing tones. S11 does not affect the pulse dialing rate. Range: Units Default 50 to 255 1 Millisecond 95 S5 Back Space Character: S5 defines the ASCII character used as a backspace to edit the command line. Range: Units Default 0 to 32 ASCII Character 8 (Back Space) XECOM (12) XE1401 XE1401 AT Registers (continued) S12 Escape Code Guard Timer: S12 sets the escape sequence guard timer. If characters are received before or after the escape sequence, within the guard timer, the modem aborts the escape attempt and remains in data mode. Range: Units Default 0 to 255 0.02 Seconds 50 Bit 5 Bit 6 Bit 7 S21 General Bit-Mapped Options: S21 reflects the state of several "AT" commands. Bit 0-2 Bit 3,4 Not Used 0 = DTR ignored (AT&D0) 1 = Enter command mode on DTR off (AT&D1) 2 = Disconnect on DTR off (AT&D2) 3 = Reset on DTR off (AT&D3) 0 = DCD always active (AT&C0) 1 = DCD on with Carrier (AT&C1) 0 = DSR always active (AT&S0) 1= DSR on when modem ready (&S1) 0 = No disconnect on Space (ATY0) 1 = Disconnect on Space (ATY1) S14 General Bit-Mapped Options: S14 reflects the state of several "AT" commands. Bit 0,4,6 Bit 1 Bit 2 Bit 3 Bit 5 Bit 7 Not Used 0 = Echo Disabled (ATE0) 1 = Echo Active (ATE1) 0 = Send Result Codes (ATQ0) 1 = No Result Codes (ATQ1) 0 = Numeric Result Codes (ATV0) 1 = Full Word Result Codes (ATV1) 0 = Tone Dialing Selected (T) 1 = Pulse Dialing Selected (P) 0 = Answer 1 = Originate S22 General Bit-Mapped Options: S22 reflects the state of several "AT" commands. Bit 0-1 0 = Low speaker volume (ATL0) 1 = Low speaker volume (ATL1) 2 = Moderate speaker volume (ATL2) 3 = High speaker volume (ATL3) Bit 2-3 0 = Speaker off (ATM0) 1 = Speaker off with carrier (ATM1) 2 = Speaker always on (ATM2) 3 = Speaker on during handshake (ATM3) Bit 4-6 0 = Basic Result codes (ATX0) 4 = Connect speed result codes (ATX1) 5 = No Blind Dial (ATX2) 6 = Busy Detection (ATX3) 7 = Full result codes (ATX4) Bit 7 Not Used S16 Test Status: S16 shows the test status of the modem Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 0 = No Local Analog Loopback 1 = Local ALB Active Not Used 0 = Local Digital Loopback Disabled 1 = Local DLB Enabled 0 = No Remote Digital Loopback 1 = Remote DLB Active 0 = Remote DLB not requested 1 = Remote DLB Requested 0 = Remote DLB w Self-Test Disabled 1 = Remote DLB w Self-Test Enabled 0 = Local ALB w Self-Test Disabled 1 = Local ALB w Self-Test Enabled Not Used S18 Test Timer: S18 determines the duration of any test. If S18 equals 0, the AT&T0 command terminates the test. Range: 0 to 255 Units Seconds Default 0 XECOM (13) XE1401 XE1401 AT Registers (continued) S23 General Bit-Mapped Options: S23 reflects the state of several "AT" commands. Bit 0 0 = Remote DLB Disabled (AT&T5) 1 = Remote DLB Allowed (AT&T4) Bit 1-3 0 = Host Interface at 300 bps 1 = Host Interface at 600 bps 2 = Host Interface at 1200 bps 3 = Host Interface at 2400 bps 4 = Host Interface at 4800 bps 5 = Host Interface at 9600 bps 6 = Host Interface at 19200 bps 7 = Host I/F at 38400 bps or higher Bit 4-5 0 = Even parity in use 1 = Not used 2 = Odd Parity in use 3 = No Parity in use Bit 6-7 0 = No Guard Tone (AT&G0) 1 = No Guard Tone (AT&G1) 2 = 1800 Hz guard tone (AT&G2) 3 = Not Used S27 General Bit-Mapped Options: S27 reflects the state of several "AT" commands. Bit 0 1 0 0 1 0 0 1 Bit 2, 4-5, 7 Bit 6 3 0 = Normal Mode (AT&Q0) 1 = Error control enabled (AT&Q5) 1 = Direct Mode (AT&Q6) Not Used S30 Disconnect on Inactivity Timer: S30 sets the time the modem is idle before it automatically disconnects . A 0 disables the inactivity timer. Range: Units Default S31 0 to 255 10 Seconds 0 General Bit-Mapped Options: S31 stores the status of various AT commands. 0 = No single-line Connect messages (AT\V0) 1 = Use single-line Connect messages (AT\V1) Bit 1 0 = No Automode detection (ATN0) 1 = Automode detection active (ATN1) Bit 2-3 0 = Report host speed (ATW0) 1 = Report all parameters (ATW1) 2 = Report modem speed only (ATW2) Bit 4-7 Not Used Bit 0 S32 XON Character: S32 determines the ASCII character to be sent as XON for in-band flow control. Range: Units Default 0 to 255 ASCII Character 11 (VT) S33 XOFF Character: S32 determines the ASCII character recognized as XOFF for in-band flow control. Range: Units Default 0 to 255 ASCII Character 19 (DC3) 0 = CCITT Protocols (ATB0) 1 = Bell Protocols (ATB1) S28 Pulse Dialing Bit-Mapped Options: S28 stores the modem's pulse dialing configuration. Bit 0-2, 5-7 Not Used Bit 3-4 0 = Make/Break ratio 39%/61%; 10 pulses per second (AT&P0) 1 = Make/Break ratio 33%/67%; 10 pulses per second (AT&P1) 2 = Make/Break ratio 39%/61%; 20 pulses per second (AT&P2) 3 = Make/Break ratio 33%/67%; 20 pulses per second (AT&P3) S29 Hook Flash Timer: S29 determines the length of time the modem closes its off-hook relay to simulate a hook switch flash on receipt of the "!" dial modifierstores the modem's pulse dialing configuration. Range: Units: Default 0 to 255 10 milliseconds 70 S36 LAPM Failure: S36 instructs the modem what to do if the error control negotiations fail. Bit 0-2 0 = Modem Disconnects 1 = Establish Direct Connection 3 = Establish normal Connection 4 = Disconnect if MNP handshake fails 5 = Establish Direct Connection if MNP handshake fails. 7 = Establish Normal Connection if MNP handshake fails. Not Used Bit 3-7 XECOM (14) XE1401 XE1401 AT Registers (continued) S37 Desired Line Speed: S37 sets the speed at which the modem begins link negotiations. Bits 0-4 0 = Automode Connection* 1-3 = 300 BPS (V.21, Bell 103) 4 = Reserved 5 = 1200 BPS (V.22, Bell 212A) 6 = 2400 BPS (V.22bis) 7 = 1200 Fwd/75 Bwd (V.23) 8 = 4800 BPS (V.32, V.32bis) 9 = 9600 BPS (V.32, V.32bis) 10 = 12,000 BPS (V.32bis) 11 = 14,400 BPS (V.32bis) 12 = 7200 BPS (V.32bis) Reserved S40 MNP Bit-Mapped Options: S40 shows the status of the modem's MNP commands, . Bit 0-1 0 = No LAPM-MNP10 conversion (-K0) 1 = Enable LAPM-MNP10 conversion (-K1) 2 = Enable LAPM-MNP10 conversion except for LAPM answer mode (-K1) Bit 2 Not Used Bits 5-7 S38 Bit 3-5 0 = AT\K0 break handling selected 1 = AT\K1 break handling selected 2 = AT\K2 break handling selected 3 = AT\K3 break handling selected 4 = AT\K4 break handling selected 5 = AT\K5 break handling selected Bit 6-7 0 = MNP Block size 64 characters 1 = MNP Block size 128 characters 2 = MNP Block size 192 characters 3 = MNP Block size 256 characters S41 General Bit-Mapped Options: S41 stores the condition of various "AT" commands. Bit 0-1 0 = No Data Compression (AT%C0) 1 = MNP5 Data Compression (AT&C1) 2 = V.42bis Data Compression (AT&C2) 3 = Either MNP5 or V.42bis Data Compression (AT&C3) 0 0 = No Fallback/Forward (AT%E0) 1 0 = Retrain Enabled (AT%E1) 0 0 = Fallback/Forward Enabled (AT%E2) Forced Disconnect Timer: S38 sets the delay between receipt of the disconnect command and the opening of the switch hook. If S38 is set to 255 the modem disconnects only after its buffers are empty. Range: Units Default 0 to 255 1 Second 20 S39 Flow Control Bit-Mapped Options: S39 shows the status of the modem's flow control options, AT&K. Bit 0-2 0 = Flow Control Disabled 3 = Hardware Flow Control, RTS/CTS 4 = In-Band Flow Control XON/XOFF 5 = Transparent In-Band Flow Control 6 = Both Harware and In-Band Flow Control S46 Bit 2, 6 Bit 3-5, 7 Not Used Data Compression Control: S46 selects whether or not the modem will support data compression with error control. S46=136 No data compression S46=138 Data Compression selected Default S48 138 Bit 3-7 Not used V.42 Negotiations: S48 determines the modem's V.42 negotiation process. S48=0 S48=7 Default 7 Proceed with LAPM Negotiate per V.42 S48=128 Assume LAPM failure XECOM (15) XE1401 XE1401 AT Registers (continued) S86 Call Failure Code: S86 shows why the last "NO CARRIER response was issued. S86=0 S86=4 S86=5 S86=9 S86=12 S86=13 S86=14 S95 Normal Disconnect Loss of Carrier V.42 Negotiation Failure Modem Handshake Failure Disconnect Initiated by remote modem No response after 10 retries Protocol Violation Extended Result Codes: S95 permits the user to customize the extended result codes. Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Connect result code shows link speed Add /ARQ to connect response Add /VFC to Carrier response Enable Protocol response Not Used Enable Compression Result Code Not used Not Used XECOM (16) XE1401 FCC Part 68 Information All equipment connected to the public telephone network in the United States must have FCC Part 68 Registration. Part 68 registration certifies that the device will not cause harm to the telephone network. The XE1401 provides a user transferable FCC Registration. This permits XE1401 customers to use our FCC registration number without submitting their systems for additional testing. Call Xecom technical support at 408-9456640 with any questions on whether your system qualifies to use Xecom's FCC Registration Number. In your operating instructions you must provide certain information to the end user of the modem. The instructions should include most of the instructions shown below. Only the information regarding the mounting of the device in the final assembly should be omitted. If your system causes harm to the telephone network, the telephone company may discontinue service temporarily. If possible, they will notify you in advance. If advance notification is not practical, you will be notified as soon as possible. Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If you experience trouble with this device, please contact XECOM at (408) 945-6640 for assistance. The telephone company may ask you to disconnect this device from the network until the problem has been corrected or until you are sure that the device is not malfunctioning. FCC Instructions: This product complies with Part 68 of the FCC Rules and Regulations. On each device shipped, there is a label which contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this product. You must, upon request, provide this information to your telephone company. The mounting of this device in the final assembly must be made in such a manner as to preserve the high voltage protection between the TIP/RING Connection and the rest of the system. Typically, this may be accomplished by maintaining a minimum spacing .100 mils between the TIP/RING Traces to the RJ-11C Jack and low voltage portion of the system. No additional circuitry may be attached between TIP/ RING and the telephone line connection, unless specifically allowed in the rules. The REN is useful to determine the quantity of devices you may connect to a telephone line and still have all of these devices ring when the number is called. In most, but not all areas, the sum of the RENs of all devices connected to one line should not exceed five (5.0). To be certain of the number of devices you may connect to the line, as determined by the REN, you should contact the local telephone company to determine the maximum REN for your calling area. The device may not be used on coin service lines provided by the telephone company (this does not apply to private coin telephone applications which use standard telephone lines). Connection to party lines is subject to state tariffs. FCC Labels: FCC rules also require a label which is visible from the outside of the equipment. The label should display Xecom's name as holder of the FCC Registration, the FCC Registration Number and Ringer Equivalence of the modem. This is the same information which appears on the top of each XE1401 module. XECOM (17) XE1401 Terms of Sale Devices sold by XECOM are covered by the warranty provisions appearing in its Terms of Sale only. XECOM makes no warranty, express, statutory, implied, or by description regarding the information set forth herein, or regarding the freedom of the described devices from patent infringement. XECOM makes no warranty of merchantability or fitness for any purposes. XECOM reserves the right to discontinue production and change specifications and prices at any time and without notice. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment, are specifically not recommended without additional processing and authorization by XECOM for such application. Xecom assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xecom product. No other circuits, patents, or licenses are implied. Life Support Policy Xecom's products are not authorized for use as Critical Components in Life Support Devices or Systems. Life Support Devices or Systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions provided in the labeling, can be reasonably expected to result in significant injury to the user. A Critical Component is any component of a life support device or system whose failure to perform can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. Copyright, Xecom (c) 1999 While Xecom, Inc. has made every effort to ensure that the information presented here is accurate, Xecom will not be liable for any damages arising from errors or omission of fact. Xecom reserves the right to modify specifications and/or prices without notice. Product mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies. Xecom Incorporated 374 Turquoise Street, Milpitas, CA 95035 Ph:408-945-6640 Fax:408-942-1346 EMail info@xecom.com Web Site www.xecom.com XECOM (18) XE1401 |
Price & Availability of XE1401
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |